[Es2] [urq] Wiring Harness
JackW at ihco.com
Wed Apr 26 19:45:45 EDT 2006
Baby with the bath water, pretty good???
Wasn't something I had control over, before it was sitting in a scrap
yard, my original goal was the harness, the fuse box, the dash,
everything. But when it went to the scrap yard, I didn't have a lot of
options. They weren't even going to let me in the yard after it got
loaded into the dump box, until they asked for the title. Told them to
bring it back...or I would call the police and say it was stolen.
The major reason I went for the fuse box surround was the lip in the
under hood area that another fuse box could eventually go on top of
along with the butyl tape. I've got a fuse box and harness from a FWD
4000 and a bunch of dash parts...? There are a ton of 4000 CSQs around
Don't things like the Ur all the dash display-speedo, tach, wiring have
to be spliced into what ever harness I end up using, On the Lighting,
A/C, Starter, rear wiper, and the battery can't I use the Ur wiring?
503) 419-4601 Direct Phone Line
503) 807-3807 Cellular Phone
From: Steve Eiche [mailto:seiche at shadetreesoftware.com]
Sent: Wednesday, April 26, 2006 5:22 PM
To: Jack Walker
Cc: Martin Pajak; es2 at audifans.com; urq at audifans.com
Subject: Re: [Es2] [urq] Wiring Harness
Well, you kind of threw away the baby with the bath water. There is no
need replace the area where the newer fusebox mounts. The area is
already properly shaped for the newer fuse box. All you need to do is
cut the hole for the housing and seal it with butyl tape (same stuff
used by the factory). It will be indistinguishable from the later fuse
box setup. You will want to remove the old fusebox bracket, and weld in
the two brackets for the relay panel, but that is all you need. You
should have saved the wiring and forgotten about the sheetmetal. You
will want CGT wiring for the rear harness(es if you have a rear wiper),
as well as the control stalks, but 4kq harnesses will work for the
rest. Either way, you will have to make some changes, especially in the
lighting circuits, A/C, starter and battery no matter what you do.
As for the RS2 harness, yes, that will work much better than the S4/S6
AAN harness. I'm not sure where Martin gets his 99% from, but I have an
RS2 harness, and while the black connector with five wires that goes to
the fuse box has them in the right places, and the fuses are easy to
connect, but the other 19 are not plug-in compatible.
Shade Tree Software, LLC
seiche at shadetreesoftware.com
Jack Walker wrote:
>You placed a 3B into the S2 harness, which is what the S2s came with,
>would I be better off with a RS2 in regard to the AAN motor?
>Was planning on getting the wiring harness out of the CGT, but after it
>sitting in my driveway for a while too long my wife decided to have it
>taken to her work where I could get the harness, fuse box, and anything
>else I wanted off. Didn't quite happen that way, got thrown, into a
>dumpster by a forklift and taken to a scrap yard.
>Hardly got the brake booster sleeve and the surrounding area of the
>box out with a torch, which I'll trim down to make the fuse box
>surround. But in cutting it out it turned most of the harness and the
>box to a smoldering mess of crap.
>503) 419-4601 Direct Phone Line
>503) 807-3807 Cellular Phone
>From: Martin Pajak [mailto:martin at quattro.ca]
>Sent: Wednesday, April 26, 2006 1:48 PM
>To: Jack Walker
>Cc: es2 at audifans.com; urq at audifans.com
>Subject: Re: [urq] Wiring Harness
>I used an S2 harness in my '85.. and 99% of wires just simply plug into
>the fusebox/original harness.. the trick here is to have a car with
>wiring and underhood fusebox.
>You can find an S2 wiring diagam at
>And RS2 is here:
>If you need some help I can scan my notes and send them your way.
>Actual wiring took me about half an hour.. but labling and preparation
>dictates how much time you actually spend under the dash with a trouble
>Hope this helps
More information about the Es2