[Es2] 6-speed

[Ben Swann]

Sean,

Thanks for the reply.  I don't understand what you mean about the axles - will 4000
Quattro axles fit the bill?  You mention 100mm - is that the inner/transmission flange
from a 4000 Quattro?  Please explain further.  If I just swap flanges from the 4kq trans
which I have and you need the ones from the RS2 trans, I may be able to do that.  I take
the flanges from the CQ trans are different.

Do you have a source for these components?  Are you selling any?  I will most likely
need the shift linkage components - any part numbers?  Anyone have Family Album for the
E cars?

Part numbers for the trans mounts/source? Do they cross-over to any domestic vehicle?
Can I use a spacer to extend CQ flanges, or chop off to make shorter?  What is different
about them?

I'm even more confused about the clutch, but will do a fit check with sever clutch
setups I have - surely the AAN clutch setup should mate with this trans. Or do they use
something different for some odd reason.  Transmission numbers for mine are:

Transmission is 6 Speed from S2 (Canadian).  Numbers are
Bellhousing:
01E 301 103	31.5230.00
Transfer Case:
01E 301211	815.0070890 	1814 V4
Final Diff:
01E 301 201 L	MWK1

Ben

-----Original Message-----
From: es2-bounces at audifans.com [mailto:es2-bounces at audifans.com] On Behalf Of Sean cole
Sent: Monday, December 24, 2007 5:03 PM
To: es2 at audifans.com
Subject: Re: [Es2] 6-speed

Ben at al.

I've got all the parts needed to do this for a V8 6-speed combo in 91 CQ.
Here is the list for an AAN CQ

1 flywheel from a 01A 7A (01A and 01E use the same splines)
1 Clutch for the 7A flywheel/6-speed (from 034 or who ever)
1 RS2 shifter (different then stock and very expensive)
1 set of RS2 front axles (or put the 100mm flanges out of a 4kq 016 into the
108mm flanges and sell me the flanges)
1 4kq drive shaft.
1 set of RS2 transmission mounts (or fabricate your own)

That is just about everything you I'm doing this from memory so I might have
missed something.

HTH
Sean
V8's rock
90 V8q getting a built 4.2L and 6-speed
91 CQ getting a V8 6-speed and much much more.



> Message: 1
> Date: Mon, 24 Dec 2007 14:19:33 -0500
> From: "Ben Swann" <benswann at verizon.net>
> Subject: Re: [Es2] knock, knock,. anyone home? ES2 Radiator choices.
> To: "'Peter Schulz'" <pcschulz at comcast.net>,    <es2 at audifans.com>
> Message-ID: <01f101c84661$ea8dc230$0201a8c0 at swansong>
> Content-Type: text/plain; charset=us-ascii
>
> Here's one for some real ES2 content - I have questions regarding
> installation of the
> RS2/ES2 6 speed transmission into the '90 Coupe Quattro.
>
> I recently got a European Spec Transmission from 6 Speed ES2 in Canada -
> supposedly the
> same transmission from an RS2.
>
> Questions are basically what else do I need to do the
> conversion/installation?
>
> The engine is an AAN from '94 S4 and has the spring loaded flywheel for
> the clutch -
> will this work OK and is this sufficient for moderate power increase over
> stock?  So far
> I have confirmed spine count is the same as for the AAN clutch disk and
> 200 clutch
> disks.  The coupe Q flywheel and clutch are different, and so definitely
> wont work with
> AAN clutch setup, but I'm installing 6 speed trans, so just trying to make
> sure the
> clutch is right.
>
> Next, I understand the transmission mounts are different, but have no
> parts numbers or
> info. on which ones to use or a source.
>
> Same with the shift linkage.  That and I understand the axle half shafts
> may be
> different length.
>
> So I'm looking for information on the 6 speed transmission conversion and
> any parts
> sources for this.  Maybe there is a kit to do this conversion.
>
> Ben
>
_______________________________________________
Es2 mailing list
Es2 at audifans.com
http://www.audifans.com/mailman/listinfo/es2